Home
1
Hot News
2
Application articles / Other
3
Basement parking lot in Taipei, Taiwan LED 4-foot microwave radar sensor tube (120cm)4
http://www.prodigital.com.tw/en/ Prodigital Technology Corp.
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
This time we introduce the performance of fully-filled LED soft strip lights. The original LED step lights used sleeved LED soft strip lights and LED glue strip lights. These two models are known in the industry as having an IP65 rating, but this approach is not recommended for use in outdoor engineering cases or LED landscape cases. Difference description: A.LED sleeve soft strip lights are actually composed of bare board + silicone sleeve, achieving dustproof and waterproof. 1. When the LED is hit by a frontal impact, the silicone sleeve is soft and does not protect the internal LED. 2. The inlet end of the casing must be properly protected to avoid water intrusion due to pulling and rupture after construction. 3. When the waterproofing of the on-site wiring is poor, water or moisture will penetrate the copper wire's cooling and heating effects, causing siphonage and water intrusion. B. LED glue strip lights are covered with a layer of PU glue on the exposed LED board to achieve dustproof and waterproof on the front. 1. The main disadvantage of the LED flexible strip light is that the back is not waterproof Outdoor lighting mainly depends on the quality of the product itself + the quality of on-site construction to extend its service life. Factory customization Recommended length: DC24V length 20 meters double-ended power supply, DC12V length 10 meters double-ended power supply Color temperature range: 2700K ~ 6500K Power range: 5W ~15W/meter, single row Waterproof level: IP68 Outlet method: 2 wire length < 10 meters Leave a waterproof layer on the front and back of the PCBA LED soft board, and tightly cover the LED and soft board. The wires are also wrapped in adhesive material, and the outer layer has a heat-shrinkable sleeve to enhance waterproofing and reduce the pulling force that may cause the adhesive material to break. After learning about the product, go to the construction site to see actual performance. Removing glue from lamp power wiring hole cover Clear the original LED glue strip lights and LED tube soft strip lights operations, Site bonding requires silicone to reinforce waterproofing Use a scraper to remove it and it will almost become crispy! Removing old silicone takes a lot of time!! Take out the arrangement position of LED soft strip lights Peel off the 3M adhesive on the back and press along the edges to fix it! After pressing, apply glue to the power hole. The 3M adhesive tape is only for temporary fixation. In actuality, the upper and lower edges of the LED flexible strip lights and the joints with the wall must be firmly covered with a layer of glue to prevent them from falling off. Fixed completed appearance Actual effect at night   LED soft strip light products https://www.prodigital.com.tw/en/product_cg257608.html Introduction to various types of LED soft strip lights  https://www.prodigital.com.tw/en/hot_362663.html http://www.prodigital.com.tw/en/hot_471661.html Taiwan Hsinchu Community Landscape LED Step Light LED Outdoor Full Glue-filled Soft Strip Light Construction Case 2024-03-01 2025-03-01
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. http://www.prodigital.com.tw/en/hot_471661.html
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. http://www.prodigital.com.tw/en/hot_471661.html
https://schema.org/EventMovedOnline https://schema.org/OfflineEventAttendanceMode
2024-03-01 http://schema.org/InStock TWD 0 http://www.prodigital.com.tw/en/hot_471661.html

LEDT8 4-foot microwave radar sensor tube performance introduction

LED radar sensor lamp manufacturer

Community description:

1. The original lamp adopts T5 fortification lamp + mountain lamp, total 174pcs

2. The car compartment is usually not open, a total of 74pcs (B2~B3)

3. The lane is always on, a total of 100pcs (B2~B3)

4. "Driveway" annual electricity bill is about $65,3184. (T5 traditional lamp holder)

Assessment focus:

1. No additional induction device is installed to avoid modifying the circuit.
2. Replace the universal lamp holder to avoid the difficulty of buying a lamp in the future.
3. The latest sense and new technology has fewer induction blind spots, saving electricity and taking into account safety lighting.
4.Automatically provide lighting during vehicle driving and parking.
5. High lumen output effectively extends the life of the lamp.

LED radar sensor lamp manufacturer

 

Installation and construction:

Hengxin Digital Technology adopts engineering-specific lamp holder packaging, and the removed lamps and lanterns can be handled properly

Avoid excessive packaging materials and create more garbage.

LED radar sensor lamp manufacturer

Construction plan:

1. Construction Quantity Table
24 B2 compartments, 34 lanes, 58 single-layer
24 B3 compartments, 34 lanes, 58 single-layer
24 B4 compartments, 34 lanes, 58 single-layer
174 in total
2. The lamp holders of the replaced lamps are concentrated and crossed.
3. Function test description: The vehicle and walking function (same specification description) are tested and accepted.
Fourth, give management personnel to implement traffic management operations during the construction period to avoid danger.
Fifth, the vehicle scheduling is arranged by the community, and the implementer will arrange the installation to keep the installation progress on schedule and avoid affecting the access of community personnel.

LED 4 feet microwave radar sensor tube installation
1. Power off installation

LED radar sensor lamp manufacturer
2. Equipped with community construction identification vest
LED radar sensor lamp manufacturer
LED radar sensor lamp manufacturer
3. Place the removed lamp holders together
LED radar sensor lamp manufacturer
4. LED 4-foot microwave radar sensor tube illuminance measurementLED radar sensor lamp manufacturer
5. Quantity calculation and acceptance
LED radar sensor lamp manufacturer
 
6. LED 4-foot microwave radar sensor tube acceptance test video
 
Product information:Push
More video:push
For more information, please go to the official website:push

Search online for "Prodigital Technology Corp"
Welcome your inquiry

自訂樣式素材

Previous Back to List Next