Hot News
Application articles / Other
LED High Bay Light install (Taiwan)4
https://www.prodigital.com.tw/en/ Prodigital Technology Corp.
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
This time we introduce the performance of fully-filled LED soft strip lights. The original LED step lights used sleeved LED soft strip lights and LED glue strip lights. These two models are known in the industry as having an IP65 rating, but this approach is not recommended for use in outdoor engineering cases or LED landscape cases. Difference description: A.LED sleeve soft strip lights are actually composed of bare board + silicone sleeve, achieving dustproof and waterproof. 1. When the LED is hit by a frontal impact, the silicone sleeve is soft and does not protect the internal LED. 2. The inlet end of the casing must be properly protected to avoid water intrusion due to pulling and rupture after construction. 3. When the waterproofing of the on-site wiring is poor, water or moisture will penetrate the copper wire's cooling and heating effects, causing siphonage and water intrusion. B. LED glue strip lights are covered with a layer of PU glue on the exposed LED board to achieve dustproof and waterproof on the front. 1. The main disadvantage of the LED flexible strip light is that the back is not waterproof Outdoor lighting mainly depends on the quality of the product itself + the quality of on-site construction to extend its service life. Factory customization Recommended length: DC24V length 20 meters double-ended power supply, DC12V length 10 meters double-ended power supply Color temperature range: 2700K ~ 6500K Power range: 5W ~15W/meter, single row Waterproof level: IP68 Outlet method: 2 wire length < 10 meters Leave a waterproof layer on the front and back of the PCBA LED soft board, and tightly cover the LED and soft board. The wires are also wrapped in adhesive material, and the outer layer has a heat-shrinkable sleeve to enhance waterproofing and reduce the pulling force that may cause the adhesive material to break. After learning about the product, go to the construction site to see actual performance. Removing glue from lamp power wiring hole cover Clear the original LED glue strip lights and LED tube soft strip lights operations, Site bonding requires silicone to reinforce waterproofing Use a scraper to remove it and it will almost become crispy! Removing old silicone takes a lot of time!! Take out the arrangement position of LED soft strip lights Peel off the 3M adhesive on the back and press along the edges to fix it! After pressing, apply glue to the power hole. The 3M adhesive tape is only for temporary fixation. In actuality, the upper and lower edges of the LED flexible strip lights and the joints with the wall must be firmly covered with a layer of glue to prevent them from falling off. Fixed completed appearance Actual effect at night   LED soft strip light products https://www.prodigital.com.tw/en/product_cg257608.html Introduction to various types of LED soft strip lights  https://www.prodigital.com.tw/en/hot_362663.html https://www.prodigital.com.tw/en/hot_471661.html Taiwan Hsinchu Community Landscape LED Step Light LED Outdoor Full Glue-filled Soft Strip Light Construction Case 2024-05-16 2025-05-16
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. https://www.prodigital.com.tw/en/hot_471661.html
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. https://www.prodigital.com.tw/en/hot_471661.html
https://schema.org/EventMovedOnline https://schema.org/OfflineEventAttendanceMode
2024-05-16 http://schema.org/InStock TWD 0 https://www.prodigital.com.tw/en/hot_471661.html

Today we will introduce an example of the installation of LED high bay lights in Taoyuan City


400-watt traditional mercury lamp, installed at a height of 13 meters


The distance between the front and rear of the lamp is 5~6 meters, and the distance between left and right is 8-9 meters
Adopt PD-HB 200W LED high bay light

PD-HB 200W

Select the best solution for analog comparison to avoid low uniformity and brightness

LED 天井燈模擬


Narrow angle degree illuminance value and effect meet the actual needs


Medium and wide-angle light is excessively diffused and the illuminance value is low, so it is not recommendedIMG_2849

Use a crane to install LED high bay lightsIMG_2826

LED high bay light installation pre-work (screw confirmation accessories to confirm)IMG_2831


Removal of 400-watt traditional mercury lampIMG_2829

Replace the LED high bay lights and hang a safety ropeIMG_2847

All LED high bay lights have been replacedIMG_2870

Traditional 400 Watt Mercury Lamp Compound Metal Lamp ConcentratedIMG_2862




Photo after installationIMG_2441

Illumination before installationIMG_2851

Illumination after installationIMG_2871

Ground illumination after installation


Difference after replacement

1. The light can be turned off at any time, no need to wait for the mercury lamp to warm up and start time
2. Lamp life can reach 50000 hours
3. Narrow angle to avoid insufficient light
4. Power is reduced by 1/2
5.5000K light is not dazzling or dim
Welcome to online inquiries and evaluations




Previous Back to List Next