Home
1
Hot News
2
Application articles / Other
3
Taiwan Radar sensor lighting installation performance Parking lot lighting installation4
http://www.prodigital.com.tw/en/ Prodigital Technology Corp.
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
This time we introduce the performance of fully-filled LED soft strip lights. The original LED step lights used sleeved LED soft strip lights and LED glue strip lights. These two models are known in the industry as having an IP65 rating, but this approach is not recommended for use in outdoor engineering cases or LED landscape cases. Difference description: A.LED sleeve soft strip lights are actually composed of bare board + silicone sleeve, achieving dustproof and waterproof. 1. When the LED is hit by a frontal impact, the silicone sleeve is soft and does not protect the internal LED. 2. The inlet end of the casing must be properly protected to avoid water intrusion due to pulling and rupture after construction. 3. When the waterproofing of the on-site wiring is poor, water or moisture will penetrate the copper wire's cooling and heating effects, causing siphonage and water intrusion. B. LED glue strip lights are covered with a layer of PU glue on the exposed LED board to achieve dustproof and waterproof on the front. 1. The main disadvantage of the LED flexible strip light is that the back is not waterproof Outdoor lighting mainly depends on the quality of the product itself + the quality of on-site construction to extend its service life. Factory customization Recommended length: DC24V length 20 meters double-ended power supply, DC12V length 10 meters double-ended power supply Color temperature range: 2700K ~ 6500K Power range: 5W ~15W/meter, single row Waterproof level: IP68 Outlet method: 2 wire length < 10 meters Leave a waterproof layer on the front and back of the PCBA LED soft board, and tightly cover the LED and soft board. The wires are also wrapped in adhesive material, and the outer layer has a heat-shrinkable sleeve to enhance waterproofing and reduce the pulling force that may cause the adhesive material to break. After learning about the product, go to the construction site to see actual performance. Removing glue from lamp power wiring hole cover Clear the original LED glue strip lights and LED tube soft strip lights operations, Site bonding requires silicone to reinforce waterproofing Use a scraper to remove it and it will almost become crispy! Removing old silicone takes a lot of time!! Take out the arrangement position of LED soft strip lights Peel off the 3M adhesive on the back and press along the edges to fix it! After pressing, apply glue to the power hole. The 3M adhesive tape is only for temporary fixation. In actuality, the upper and lower edges of the LED flexible strip lights and the joints with the wall must be firmly covered with a layer of glue to prevent them from falling off. Fixed completed appearance Actual effect at night   LED soft strip light products https://www.prodigital.com.tw/en/product_cg257608.html Introduction to various types of LED soft strip lights  https://www.prodigital.com.tw/en/hot_362663.html http://www.prodigital.com.tw/en/hot_471661.html Taiwan Hsinchu Community Landscape LED Step Light LED Outdoor Full Glue-filled Soft Strip Light Construction Case 2024-03-01 2025-03-01
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. http://www.prodigital.com.tw/en/hot_471661.html
Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. http://www.prodigital.com.tw/en/hot_471661.html
https://schema.org/EventMovedOnline https://schema.org/OfflineEventAttendanceMode
2024-03-01 http://schema.org/InStock TWD 0 http://www.prodigital.com.tw/en/hot_471661.html

This case is located in Zhunan Community, Miaoli, Taiwan

The original builder retained the T5 4-foot double lamp holder + infrared sensor + time control parking lot lighting

社區停車場

紅外線感應器

T5燈具

The community has assessed the options after replacing the lamp holder due to age:

1. 1 LED 4-foot lamp holder or 2 LED 4-foot lamp holders

2. Two LED 4-foot lamps are always on with a timer

3. Two LED 4-foot lamps are always on with a light controller

3. 1 LED 4-foot light tube with constant light, 1 LED 4-foot light tube with radar sense light tube, additionally equipped with a total timer

4. 1 LED 4-foot light tube is always on, 1 LED 4-foot light controller controls or part of the location area

5. 1 lamp tube LED 4 feet constant light, 1 lamp tube timer control part of the position area

6.1 LED 4-foot radar control, 1 LED 4-foot independent timing controller, additional total timer

After discussion in the community, choose 1 light tube LED 4 feet radar control, 1 light tube LED 4 feet independent timing controller, and additionally configure a total timer

Turn on the lights at 18:00 every night from Monday to Sunday, and keep the double lights running until after 22:00 in the evening.

Keep the radar sensor lamp and turn off the constant light until it is turned off at 06:00 the next morning.

Site survey confirms whether the circuit operates independently

IMG_9884

Originally, a 24-hour timing controller was used, with 15 minutes per division and 4 divisions per hour.

And independent two timers, one car lane uses another car parking space.

After the site survey found that the second half of the car grid is connected in parallel with the community access control + camera, it is necessary to check the circuit and separate them for independent control.

Lamp holder modification work

IMG_0487

IMG_0448

IMG_0495

After testing all lamp sockets, reduce the packaging materials such as lamp tubes to the minimum.

Improve construction speed and quality.

IMG_0924

The original infrared sensor was removed and restored to its original state.

IMG_0925

75895

IMG_0942

Install the LED sensor lights and LED tubes in order and clean the spider webs.

IMG_0943

Disassemble the lamps and put them away in a centralized manner, and collect them while constructing.

75900

IMG_0928

Check and disconnect the circuit.

75911

IMG_0958

Installation and positioning of the rear parking meter

IMG_0977

IMG_0998

Installation and positioning of parking space timing in front of the total lane

IMG_0992

IMG_0995

IMG_0997

label marking

IMG_0948

Centralized to designated location for storage

Provide acceptance data and timer electronic files and on-site operation teaching videos

IMG_1916

Double lamp general lamp + radar sensor lamp effect

IMG_1929-1

The radar sensor lamp maintains the effect of 18W

IMG_1930-1

The radar lamp on the left of the photo has a brightness of 18W, and the brightness of the radar lamp on the right has a brightness of 6W.

IMG_1908

兩支燈管全亮20W+18W最高亮度300Lux

IMG_1921.MOV_000001800

全區剩下感應燈6W照度值

Previous Back to List Next